9.5. Using Printers

This section tells you how to use printers you have setup with FreeBSD. Here is an overview of the user-level commands:

lpr(1)

Print jobs

lpq(1)

Check printer queues

lprm(1)

Remove jobs from a printer's queue

There is also an administrative command, lpc(8), described in the section Administrating the LPD Spooler, used to control printers and their queues.

All three of the commands lpr(1), lprm(1), and lpq(1) accept an option -P printer-name to specify on which printer/queue to operate, as listed in the /etc/printcap file. This enables you to submit, remove, and check on jobs for various printers. If you do not use the -P option, then these commands use the printer specified in the PRINTER environment variable. Finally, if you do not have a PRINTER environment variable, these commands default to the printer named lp.

Hereafter, the terminology default printer means the printer named in the PRINTER environment variable, or the printer named lp when there is no PRINTER environment variable.

9.5.1. Printing Jobs

To print files, type:

    % lpr filename ...

This prints each of the listed files to the default printer. If you list no files, lpr(1) reads data to print from standard input. For example, this command prints some important system files:

    % lpr /etc/host.conf /etc/hosts.equiv

To select a specific printer, type:

    % lpr -P printer-name filename ...

This example prints a long listing of the current directory to the printer named rattan:

    % ls -l | lpr -P rattan

Because no files were listed for the lpr(1) command, lpr read the data to print from standard input, which was the output of the ls -l command.

The lpr(1) command can also accept a wide variety of options to control formatting, apply file conversions, generate multiple copies, and so forth. For more information, see the section Printing Options.

9.5.2. Checking Jobs

When you print with lpr(1), the data you wish to print is put together in a package called a ``print job'', which is sent to the LPD spooling system. Each printer has a queue of jobs, and your job waits in that queue along with other jobs from yourself and from other users. The printer prints those jobs in a first-come, first-served order.

To display the queue for the default printer, type lpq(1). For a specific printer, use the -P option. For example, the command

    % lpq -P bamboo
shows the queue for the printer named bamboo. Here is an example of the output of the lpq command:

    bamboo is ready and printing
    Rank   Owner    Job  Files                              Total Size
    active kelly    9    /etc/host.conf, /etc/hosts.equiv   88 bytes
    2nd    kelly    10   (standard input)                   1635 bytes
    3rd    mary     11   ...                                78519 bytes

This shows three jobs in the queue for bamboo. The first job, submitted by user kelly, got assigned ``job number'' 9. Every job for a printer gets a unique job number. Most of the time you can ignore the job number, but you will need it if you want to cancel the job; see section Removing Jobs for details.

Job number nine consists of two files; multiple files given on the lpr(1) command line are treated as part of a single job. It is the currently active job (note the word active under the ``Rank'' column), which means the printer should be currently printing that job. The second job consists of data passed as the standard input to the lpr(1) command. The third job came from user mary; it is a much larger job. The pathname of the files she's trying to print is too long to fit, so the lpq(1) command just shows three dots.

The very first line of the output from lpq(1) is also useful: it tells what the printer is currently doing (or at least what LPD thinks the printer is doing).

The lpq(1) command also support a -l option to generate a detailed long listing. Here is an example of lpq -l:

    waiting for bamboo to become ready (offline ?)
    kelly: 1st               [job 009rose]
           /etc/host.conf                    73 bytes
           /etc/hosts.equiv                  15 bytes
    
    kelly: 2nd               [job 010rose]
           (standard input)                  1635 bytes
    
    mary: 3rd                                [job 011rose]
          /home/orchid/mary/research/venus/alpha-regio/mapping 78519 bytes

9.5.3. Removing Jobs

If you change your mind about printing a job, you can remove the job from the queue with the lprm(1) command. Often, you can even use lprm(1) to remove an active job, but some or all of the job might still get printed.

To remove a job from the default printer, first use lpq(1) to find the job number. Then type:

    % lprm job-number

To remove the job from a specific printer, add the -P option. The following command removes job number 10 from the queue for the printer bamboo:

    % lprm -P bamboo 10

The lprm(1) command has a few shortcuts:

lprm -

Removes all jobs (for the default printer) belonging to you.

lprm user

Removes all jobs (for the default printer) belonging to user. The superuser can remove other users' jobs; you can remove only your own jobs.

lprm

With no job number, user name, or - appearing on the command line, lprm(1) removes the currently active job on the default printer, if it belongs to you. The superuser can remove any active job.

Just use the -P option with the above shortcuts to operate on a specific printer instead of the default. For example, the following command removes all jobs for the current user in the queue for the printer named rattan:

    % lprm -P rattan -

Note: If you are working in a networked environment, lprm(1) will let you remove jobs only from the host from which the jobs were submitted, even if the same printer is available from other hosts. The following command sequence demonstrates this:

    % lpr -P rattan myfile
    % rlogin orchid
    % lpq -P rattan
    Rank   Owner      Job  Files                          Total Size
    active seeyan     12    ...                           49123 bytes
    2nd    kelly      13   myfile                         12 bytes
    % lprm -P rattan 13
    rose: Permission denied
    % logout
    % lprm -P rattan 13
    dfA013rose dequeued
    cfA013rose dequeued
       

9.5.4. Beyond Plain Text: Printing Options

The lpr(1) command supports a number of options that control formatting text, converting graphic and other file formats, producing multiple copies, handling of the job, and more. This section describes the options.

9.5.4.1. Formatting and Conversion Options

The following lpr(1) options control formatting of the files in the job. Use these options if the job does not contain plain text or if you want plain text formatted through the pr(1) utility.

For example, the following command prints a DVI file (from the TeX typesetting system) named fish-report.dvi to the printer named bamboo:

    % lpr -P bamboo -d fish-report.dvi

These options apply to every file in the job, so you cannot mix (say) DVI and ditroff files together in a job. Instead, submit the files as separate jobs, using a different conversion option for each job.

Note: All of these options except -p and -T require conversion filters installed for the destination printer. For example, the -d option requires the DVI conversion filter. Section Conversion Filters gives details.

-c

Print cifplot files.

-d

Print DVI files.

-f

Print FORTRAN text files.

-g

Print plot data.

-i number

Indent the output by number columns; if you omit number, indent by 8 columns. This option works only with certain conversion filters.

Note: Do not put any space between the -i and the number.

-l

Print literal text data, including control characters.

-n

Print ditroff (device independent troff) data.

-p

Format plain text with pr(1) before printing. See pr(1) for more information.

-T title

Use title on the pr(1) header instead of the file name. This option has effect only when used with the -p option.

-t

Print troff data.

-v

Print raster data.

Here is an example: this command prints a nicely formatted version of the ls(1) manual page on the default printer:

    % zcat /usr/share/man/man1/ls.1.gz | troff -t -man | lpr -t

The zcat(1) command uncompresses the source of the ls(1) manual page and passes it to the troff(1) command, which formats that source and makes GNU troff output and passes it to lpr(1), which submits the job to the LPD spooler. Because we used the -t option to lpr(1), the spooler will convert the GNU troff output into a format the default printer can understand when it prints the job.

9.5.4.2. Job Handling Options

The following options to lpr(1) tell LPD to handle the job specially:

-# copies

Produce a number of copies of each file in the job instead of just one copy. An administrator may disable this option to reduce printer wear-and-tear and encourage photocopier usage. See section Restricting Multiple Copies.

This example prints three copies of parser.c followed by three copies of parser.h to the default printer:

    % lpr -#3 parser.c parser.h
-m

Send mail after completing the print job. With this option, the LPD system will send mail to your account when it finishes handling your job. In its message, it will tell you if the job completed successfully or if there was an error, and (often) what the error was.

-s

Do not copy the files to the spooling directory, but make symbolic links to them instead.

If you are printing a large job, you probably want to use this option. It saves space in the spooling directory (your job might overflow the free space on the filesystem where the spooling directory resides). It saves time as well since LPD will not have to copy each and every byte of your job to the spooling directory.

There is a drawback, though: since LPD will refer to the original files directly, you cannot modify or remove them until they have been printed.

Note: If you are printing to a remote printer, LPD will eventually have to copy files from the local host to the remote host, so the -s option will save space only on the local spooling directory, not the remote. It is still useful, though.

-r

Remove the files in the job after copying them to the spooling directory, or after printing them with the -s option. Be careful with this option!

9.5.4.3. Header Page Options

These options to lpr(1) adjust the text that normally appears on a job's header page. If header pages are suppressed for the destination printer, these options have no effect. See section Header Pages for information about setting up header pages.

-C text

Replace the hostname on the header page with text. The hostname is normally the name of the host from which the job was submitted.

-J text

Replace the job name on the header page with text. The job name is normally the name of the first file of the job, or stdin if you are printing standard input.

-h

Do not print any header page.

Note: At some sites, this option may have no effect due to the way header pages are generated. See Header Pages for details.

9.5.5. Administrating Printers

As an administrator for your printers, you have had to install, set up, and test them. Using the lpc(8) command, you can interact with your printers in yet more ways. With lpc(8), you can

First, a note about terminology: if a printer is stopped, it will not print anything in its queue. Users can still submit jobs, which will wait in the queue until the printer is started or the queue is cleared.

If a queue is disabled, no user (except root) can submit jobs for the printer. An enabled queue allows jobs to be submitted. A printer can be started for a disabled queue, in which case it will continue to print jobs in the queue until the queue is empty.

In general, you have to have root privileges to use the lpc(8) command. Ordinary users can use the lpc(8) command to get printer status and to restart a hung printer only.

Here is a summary of the lpc(8) commands. Most of the commands takes a printer-name argument to tell on which printer to operate. You can use all for the printer-name to mean all printers listed in /etc/printcap.

abort printer-name

Cancel the current job and stop the printer. Users can still submit jobs if the queue's enabled.

clean printer-name

Remove old files from the printer's spooling directory. Occasionally, the files that make up a job are not properly removed by LPD, particularly if there have been errors during printing or a lot of administrative activity. This command finds files that do not belong in the spooling directory and removes them.

disable printer-name

Disable queuing of new jobs. If the printer's started, it will continue to print any jobs remaining in the queue. The superuser (root) can always submit jobs, even to a disabled queue.

This command is useful while you are testing a new printer or filter installation: disable the queue and submit jobs as root. Other users will not be able to submit jobs until you complete your testing and re-enable the queue with the enable command.

down printer-name message

Take a printer down. Equivalent to disable followed by stop. The message appears as the printer's status whenever a user checks the printer's queue with lpq(1) or status with lpc status.

enable printer-name

Enable the queue for a printer. Users can submit jobs but the printer will not print anything until it is started.

help command-name

Print help on the command command-name. With no command-name, print a summary of the commands available.

restart printer-name

Start the printer. Ordinary users can use this command if some extraordinary circumstance hangs LPD, but they cannot start a printer stopped with either the stop or down commands. The restart command is equivalent to abort followed by start.

start printer-name

Start the printer. The printer will print jobs in its queue.

stop printer-name

Stop the printer. The printer will finish the current job and will not print anything else in its queue. Even though the printer is stopped, users can still submit jobs to an enabled queue.

topq printer-name job-or-username

Rearrange the queue for printer-name by placing the jobs with the listed job numbers or the jobs belonging to username at the top of the queue. For this command, you cannot use all as the printer-name.

up printer-name

Bring a printer up; the opposite of the down command. Equivalent to start followed by enable.

lpc(8) accepts the above commands on the command line. If you do not enter any commands, lpc(8) enters an interactive mode, where you can enter commands until you type exit, quit, or end-of-file.

For questions about FreeBSD, e-mail <questions@FreeBSD.org>.
For questions about this documentation, e-mail <doc@FreeBSD.org>.